-
product
PC Based Test Setup for LED PCB of Luminaire
The panel carries out different tests one by one and provides indication of the Test results as OK or NOT-OK. It is very useful and handy in line testing on Mass production line as well as type Testing. Special fixture can be provided for the specific product. This avoids the connections & disconnections of the product for different tests. The total time for entire testing is less than 40 seconds.
-
product
AC Hysteresis Graph Test System
DX-2012SA
Under continuous frequency of 1 kHz to 500 kHz, automatic measurement of magnetic hysteresis loop of the soft magnetic materials such as silicon steel, precision alloy, non-crystal and ferrite, accurate measurement on the dynamic magnetic characteristic parameters such as amplitude permeability µa, loss angle d, loss iron Pc, remanence Br and coercivity Hc.
-
product
AUTOMATIC WINDING TEST SYSTEM
VE9036SU
6 CHANNEL Microprocessor based Automatic Test System for Automobile Coils, Magnetos, Alternator, Motor Winding. Can Test : Impulse Winding Tester (IW), AC/DC HiPot, Insulation Resistance (IR), Inductance (L), DC Resistance (DCR)
-
product
2-Channel Mandrel Free IL/RL Test Station
Shanghai Fibretool Technology Co.,Ltd.
This test station is designed specially for different connector on both sides patch cord(such as FC-SC, FC-LC, SC-LC…) and the duplex patch cord.The REF for insertion and return loss can set one time for those kind of patch cord, no need to change standard patch cord and interchange testing port connector on tester( Especially 2.5mm and 1.25mm interchange). For the tested patch cord, APC end no need to manually set standard patch cord length if PC end measured shortest length is 2.2M.
-
product
Thermal Shock Test Chamber (Three Zone)
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell’s Thermal Shock Test Chamber (3 Zone) consist of the Test Zone, Heat Storage Zone and Cold Storage Zone. The specimen stay in test zone, hot and cold air will be blew from the storage zones to achieve rapid temperature change for thermal shock.
-
product
Electrostatic Discharge Test
The electrostatic discharge test is designed to determine the ability of equipment to perform its intended function without permanent degradation of performance as a result of an air discharged electrostatic pulse. Electrostatic discharge is the result of an unbalanced electrical charge. Typically, it is created by insulator surfaces rubbing together or pulling apart. A transfer of electrostatic charge between bodies (materials, components, etc.) at different electrostatic potentials is caused by direct contact.
-
product
JD Edwards Test Automation
Dimension Swiftest
Dimension SwifTest™ has been designed specifically for EnterpriseOne. It is the easiest way to set up and execute your testing without the need for specialist test engineers or programmers. Business Analysts and Super-Users can now build their own test scripts and scenarios quickly and easily using Dimension SwifTest.
-
product
RF Test Spectrum Measurements over CPRI
Integris 3000
Most modern cell tower network configurations place the Remote Radio Head (RRH) at the top of the tower and the baseband unit(BBU) at the bottom of the tower. While this configuration is advantageous for both computational efficiency and mitigation of RF loss across the cable, it means the only place along RF can be accessed is at the top of the tower. This forces field technicians to have to climb the tower to measure and debug RF noise problems.
-
product
In-Circuit Test Fixture Design Services
An integral part of board test is the test fixture. Innovations in board technology may manifest themselves as challenges in test fixture design. Utilizing a creative & systematic design philosophy, Acculogic consistently delivers state of the art solutions for the most complex test interface problems.
-
product
Acoustic Test Chamber
For the development of small devices and components. Reliable measuring environment for noise tests and quality assurance.
-
product
10 MHz To 67 GHz LAN Wide Dynamic Range Average Power Sensor
L2057XA
Accurately measure any modulated signal with the Keysight Technologies, Inc. U/L2050/60 X-Series wide dynamic range power sensors. The USB/LAN connectivity models come with a wide dynamic range, covering -70 to +26 dBm. This sensor offers very accurate and repeatable power measurements for any modulated signal and comes with a super-fast measurement speed of 50,000 readings/sec, which enables higher manufacturing throughput. Users can also save time and reduce measurement uncertainty with the in...show more -
product
Audio Test Tone Generator
ToneGenerator
Tone Generator is a sine wave generator, frequency generator and signal generator that lets you create audio test tones, sweeps or noise waveforms using your computer or a PDA handheld. Generate sine wave, square wave, triangular waveform, saw tooth waveform, impulse, white noise and pink noise.
-
product
Vibration Test Systems
G-9 Series
The G-9 Series Vibration Test Systems, featured by high eccentric moment and a large loading table supported by the unique rigid lateral suspension structure, are suited to transportation tests for relatively large specimens; packaged goods and electric apparatus. In addition, the unique structure enables horizontal tests of relatively heavy specimens without conventional horizontal slip tables.
-
product
In-Line 2-Module In-Circuit Test System; i337x, Series 5i
E9988E
Short wire fixturing eliminates problems commonly found with long wire fixturing, such as noise and deterioration of test stability. This translates into transportable, repeatable and stable tests on your i3070 Series 5i, even if you need to deploy tests halfway across the globe, or on different manufacturing sites.
-
product
Mixed Signal Test Systems
MTS1020i
The MTS-1020i is a cost effective production ATE designed for testing high-volume linear and mixed signal semiconductor devices (Op Amps, high-voltage drivers, DAC, ADC, etc.), both at the wafer sort and final test stages of the manufacturing process
-
product
Gas-insulated AC Test System
Yangzhou Power Electric Co., Ltd
The test system is used to do AC voltage withstand test and PD measurement for high voltage insulation products, combined electrical equipment, instrument transformers, etc.
-
product
CT/VT Test System
Fully pre-wired comprehensive turn test system. *Suitable for CTs up to 6000A & VTs up to 132kV. * Precision to (0.005 class) internal multi-ratio standard CT. * Internal 4KA current source. * State-of-the-art Instrument Transformer Test Set AITTS-98 with computer & printer interfaces. * Electronic potential divider facilitates testing any VT ratio upto 132kV. * Current & potential burdens.
-
product
High Parallel Test Of Barometric Pressure Sensors
InBaro
InBaro MEMS module, a proven solution for accurate barometric sensor test with high throughput and stability.
-
product
Test Chamber for Dynamic Vibrators
The focus of the Feutron climate simulation overall concept is on the simplest operation of the overall functions of the test systems and the highest reliability with maximum efficiency. This is why our systems are supplied as plug-in compact devices.
-
product
DC System and Battery Test Instruments
Wuhan Huatian Electric Power Automation Co., Ltd.
DC System and Battery Test Instruments by HVTEST
-
product
Test Sockets
socket design as per customer specificationsquick + easy socket changehigh-performance spring probesdesigned for high frequency up to 16 GHz-55C/-67F to 150C/302F temperature rangemanual/automatic application optionssmall socket footprintone socket base for each insert (3x3 to 9x9 QFN)one-click switch from engineering to production socket modedevice dependent standard socket frame with changeable insertmore than 500,000 compression cyclesKelvin test applicabilitytool-free insert + actuator exchanges0.3 mm minimum lead pitchQFP extender available
-
product
Mechanical Bench-top Test Jigs
CGF Series
Advanced test jig, using a cam-operated, fully adjustable gate - self customisation.
-
product
Semiconductor Test Services
Tests regarding function, electrical and optoelectronical parameter. Electrical test of wafer up to 8? and packaged devices - selection and volume test.
-
product
Universal Test Fixture
CAM/GATE
The Low Cost Solution for Accurate and Dependable Universal Functional TestThe CAM/GATE ® Universal Test Fixture System is your afforable, efficient solution for functional test. No need to have multiple fixtures in your test area...
-
product
Test Systems
This measurement system is the state-of-the-art acoustical analyser from Norsonic. Using the experiences and accumulated know-how from the previous generations of analysers, Norsonic is offering a multi-channel system with focus on user friendliness, high efficiency, and accurate reporting. The system has been designed for field testing as well as demanding accredited lab measurements.
-
product
Ethernet Test and Simulation Instruments for Speeds from 10 Mbit/s to 25 Gbit/s
Avionics Interface Technologies
AIT’s Ethernet test instruments provide Ethernet test features for 10Mbit, 100Mbit, 1Gbit, and 10Gbit Ethernet networks, for both Optical and Copper media. All instruments are supported by Analyzer and Simulator software applications (GUIs) and additionally software API’s allowing integration into user applications.
-
product
Portable Test Systems
We refer to test meters with an integrated source as test systems. Test systems are particularly useful when you need custom current and voltage values when testing meter installations, but only want to use a single device.
-
product
Test Prods
Test prod with 4mm plug, test prod with 2mm pin, safety test prod, test prod 2mm, test prod 4mm, miniature test prod.
-
product
Radiographic Inspection Test
The radiographic inspection is a non-destructive x-ray method for detecting internal physical defects in small component parts which are not otherwise visible. Radiographic techniques are intended to reveal such flaws as improper positioning of elements, voids in encapsulating or potting compounds, inhomogeneities in materials, presence of foreign materials, broken elements, etc.
-
product
Modular Hydrostatic Test System
Our modular hydrostatic test chambers are designed with open ends to accommodate the connection to similar units for the purpose of lengthening the enclosed test area. The modular test system starts with a base unit with complete pump system, gauges and controls mounted on the 60” x 24” x 18” test chamber. If longer test lengths are required, simply add another test chamber to double, triple or quadruple the test length area. Specify your particular requirements at our Customization Page.